Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
The writer is making a few good observations related to Tools You Need to Install a New Bathtub in general in the article on the next paragraphs.
Mounting a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, as well as sometimes, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult job. If the old tub is conveniently available, the task can move rapidly; if you need to open up a wall to remove the old tub as well as position the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the brand-new one. Ensure you have actually certified on your own for the task and also fit attempting it. Instead of hiring a service provider to take over a halfway-completed job, it is better to think about using one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This short article will certainly assist you set up a new bathtub in your shower room if you have actually currently bought a new bathtub as well as do not need to change the plan of your previous water system pipelines.
Your tools and also material checklist should make up the following:
Preparing for the Setup
First of all, the sustaining frame provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its last position.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome because of the limited access that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been removed, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Mounting the Tub
Utilizing the two wood boards under its feet, put the bathtub in the required position. The wood boards are helpful in evenly spreading out the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the level and adjusting the feet on the tub up until the spirit level checks out level.
To set up taps, fit all-time low of the outermost versatile tap connector to the suitable supply pipe by making a compression join; then do the very same for the various other tap.
Turn on the water supply and inspect all joints and also brand-new pipework for leaks as well as tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and the regular outlet for leakages.
Lastly, repair the bathroom paneling as described in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been utilized at the very least once as this will certainly settle it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin making sure that the washing machines are in location between the faucet and the sink. Secure the faucet in position with the supplier provided backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type should be linked to the faucet finishes initially, tightening only by hand. The supply pipelines can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, causing the water to penetrate the wall surface between the bathroom and also the tiling, bring about problems with moisture as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and also fittings. They are sold in tubes and also cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to securing, to allow for the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the market. It is recommended to fit the tiles using waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that report about How to Install a Bathtub from a good friend on a different web address. In case you enjoyed reading our blog entry plz do not forget to pass it around. We treasure reading our article about How to Install a Bathtub Yourself.
Search-end for emergency plumbing. Report this page